Matek PDB-XT60 W/BEC 5V and 12V ₹369.00
Mauch 074: HS -100-HV , 4-14S Sensor ₹4,945.00
- 200A?? Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.
- This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.
Mauch 076: HS-200-HV ,200A Sensor
₹5,118.00 excl. GST
Output 5.30V / 3A -> +/- 0.05V ?> Ripple 1mV @ 1.5A output current.. Delivery in PP box: 55 x 55 x 20mm. 1x? 021: PL 4-14S HYB-BEC / 1x 5.3V / 3A. 1x? 040: PL ? Series sensor cable / L=150mmMAUCH 021: PL 4-14S HYB-BEC / 1x 5.3V For UAV /Drones
₹6,670.00 excl. GST
- 100A?? Current measurement sensor board, based on Allegro Hall Sensor ACS-100U.
- This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.
Mauch 074: HS -100-HV , 4-14S Sensor
₹4,945.00 excl. GST
- Measures current up to 200A and Voltage upto 20S (Max. 85V) with solder bridge open and up to 7S (max. 30V) with solder bridge closed .
- 1x 200A current and voltage measurement sensor, based on Allegro Hall Sensor ACS758-200U, 2x 15cm 8AWG wires (red), Molex CLIK-Mate 1.25mm 4p connector
- 1x CFK enclosure
Mauch MH-004 PL 200 Sensor board With CFK Enclosue
₹5,693.00 excl. GST
- Output 5.3V / 3A -> +/- 0.05V.
- Input 4-14S LiPo / max. 60V.
Mauch 085: 4-14S BEC Pixhawk 2.1
₹4,945.00 excl. GST
This cable is for the PL-Series BEC?s to connect to Cube/Pixhawk 2.1 or any other flight controller with a 6pin Molex CLIK-Mate2.0 connector.Mauch 042 PL Cable for Pixhawk 2.1 / Mate
₹633.00 excl. GST
Mauch 017: PL 4-6S BEC 2×5.35V 1×12.0V with CFK enclosure
₹8,395.00 excl. GST
Mauch 003: PL-200 Sensor Board with CFK enclosure
₹5,279.00 excl. GST
- Input and output is protected by Panasonic FC / FM capacitors.
- Input 4-14S LiPo / max. 60V?.
- Output 5.3V / 3A -> +/- 0.05V.
Mauch 084: 4-14S BEC (HS series)
₹4,485.00 excl. GST
- 200A?? Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.
- The BEC will also power the flight controller as well as the attached equipment like GPS, telemetry? etc.
Mauch 075: HS-200-LV , 200A Sensor
₹5,118.00 excl. GST
- Power-Cube 3 ?V3? with 3 outputs 2x 5.3V / 10A + 1x 12.0V / 10A
- Input voltage 4-14S, max. 60V
Mauch 053: PC3 / V3 Sensor
₹28,750.00 excl. GST
Mauch 024: PL 4-14S HYB-BEC / 2×5.3V / 1×12.0V
₹16,099.00 excl. GST
- This sensor hub allows to connect two PixHawk Mauch current sensors in parallel in order to add their current capacities.
- The current of both sensors is summarized before reaching the flight controller while the voltage measurement of the LiPo packs are collected from both sensors and passed through the hub to the flight controller.
- The main purpose of this hub is to replace existing protection circuits and to monitor that both paralleled LiPos are supplying the same current to the system.
- Thanks to Mauch Sensor Hub X2, you can spot early when a LiPo starts to fail, way before this situation is irreversible.
- In case of difference in current is of +/- 15%, the alarm output goes ON in order to indicate the fault. The pilote should then land immediately in order to check the batteries.
Mauch 010: PL Sensor Hub X2-V2 with CFK enclosure for UAV/DRONES
₹5,808.00 excl. GST
Mauch 090 ? 4-14S HYB-BEC / 12V-3A / 2x 20cm 24AWG
₹4,140.00 excl. GST- Out Of Stock
Connects a Sensor Board to the SEN. port on a PL BEC, a Sensor Hub X2, a Sensor Hub X8, or a Power-CubeYou can also use this cable to retrofit your own BECMolex CLIK-Mate 1.25mm 4p on both ends / L = 150mmMauch 040: PL Sensor Cable
₹575.00 excl. GST
