Your bag is empty
Don't miss out on great deals! Start shopping or Sign in to view products added.
Shop What's New Sign in-
- 200A?? Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.
- The BEC will also power the flight controller as well as the attached equipment like GPS, telemetry? etc.
Mauch 075: HS-200-LV , 200A Sensor
₹4,450.00 excl. GST -
Out Of Stock
Connects a Sensor Board to the SEN. port on a PL BEC, a Sensor Hub X2, a Sensor Hub X8, or a Power-Cube You can also use this cable to retrofit your own BEC Molex CLIK-Mate 1.25mm 4p on both ends / L = 150mmMauch 040: PL Sensor Cable
₹500.00 excl. GST -
- This sensor hub allows to connect two PixHawk Mauch current sensors in parallel in order to add their current capacities.
- The current of both sensors is summarized before reaching the flight controller while the voltage measurement of the LiPo packs are collected from both sensors and passed through the hub to the flight controller.
- The main purpose of this hub is to replace existing protection circuits and to monitor that both paralleled LiPos are supplying the same current to the system.
- Thanks to Mauch Sensor Hub X2, you can spot early when a LiPo starts to fail, way before this situation is irreversible.
- In case of difference in current is of +/- 15%, the alarm output goes ON in order to indicate the fault. The pilote should then land immediately in order to check the batteries.
Mauch 010: PL Sensor Hub X2-V2 with CFK enclosure for UAV/DRONES
₹5,050.00 excl. GST -
- SVMFG M3001X - DF13 4-14S HYB BEC / 5.30V DF-13-4P
- 4-14S LiPo (Max 60V)
- 5.35V at 3A stable power
- DF-13-4P for seamless sensor hub integration
SVMFG M3001X – DF13 4-14S HYB BEC
₹3,040.00 excl. GST -
Mauch 060 ? Power Cube to Pixhawk 2.1 Cable
₹649.00 excl. GST -
Mauch 043 ? PL ? FC cable for JST-GH 6pin
₹699.00 excl. GST -
- 200A- Current measurement sensor board, based on Allegro Hall Sensor ACS-250U.
- The voltage reading of the LiPo is optimized for up to 14S LiPo packs.
- This Sensor board needs a power supply. So please select the matching BEC according to your preference from the BEC section.
- The BEC will also power the flight controller as well as the attached equipment like GPS, telemetry... etc.
- Connected to the sensor are 2x10cm AWG10 wire (red) as a standard.
-
The board comes with a 10cm connection cable (DF-13-6p <-> DF-13-6p) to the FC. If you need a customized cable in different lengths, then please order it separately.
Mauch MH076: HS-200-HV Sensor Board / 2x 10cm 10AWG
₹4,200.00 excl. GST -
- Weight: 2.6kg
- Maximum torque: 300 N.cm
- Input voltage: DC 12V~15V
- Average power consumption: 15W
- Working temperature: -20~60?
- IP level: 65
Taisync’s ViuTracker G1
-
Max Voltage 12S Capacitance 2800uF Type Electrolytic Current Rating (PCB) 250A Voltage ripple reduction YesReflex Drive Capacitor CAP BANK
₹2,000.00 excl. GST -
4-14S HYBRID BEC with Multiple Outputs Dual 5.35V Single 5.0V Single 12VSVMFG M3004X – 4CH, 4-14S HYBRID BEC
₹13,920.00 excl. GST
